CCNA Practice Test 10 – Free Tech Exams

You have been put in charge or securing the Cisco devices the business network. Upon investigating you find they have only had telnet configured for remote access management. You decide you must use SSH Version 2 and have confirmed this is supported on all the devices. What actions should you take to configure and use SSH 2 on each device?

A. Initialize a user local database. Set a hostname and domain-name. Create a RSA key and username with a minimum of 768 bits. Set the system to use SSH Version 2. Configure the VTY terminals to use the local database for logins.

B. Set a hostname and domain-name. Enable a secret password. Add user accounts with a password. Create a RSA key with a minimum of 768 bits. Set the system to use SSH Version 2. Configure the VTY terminals to use the local database for logins.

C. Initialize a user local database. Add user accounts with a password. Create a RSA key with a minimum of 512 bits. Set the system to use SSH Version 2.

D. Set a hostname and domain-name. Create a system session password. Add session accounts. Create a RSA key with a minimum of 2048 bits. Set the system to use SSH Version 2. Configure the VTY terminals to use Kerberos sessions.

Your company recently purchased some IP phones for the call center department and you are tasked with setting up the access layer switch to support the IP phones. The requirement is to includes create VLANs and support both VoIP phone and PC data on the same access port without the need for a trunk. What VLAN configuration will you apply to the access layer switch to support voice traffic on VLAN 10 and data on VLAN 20?

A. ASW1(config-if)#switchport mode access ASW1(config-if)#switchport access vlan 10 ASW1(config-if)#switchport voice vlan 20

B. ASW1(config-if)#switchport mode trunk ASW1(config-if)#switchport access vlan 20 ASW1(config-if)#switchport voice vlan 10

C. ASW1(config-if)#switchport mode trunk ASW1(config-if)#switchport access vlan 20 ASW1(config-if)#switchport vlan voip 10

D. ASW1(config-if)#switchport mode trunk ASW1(config-if)#switchport voice vlan 10 ASW1(config-if)#switchport access vlan 20

You are configuring the default route for an IPv4 network on multiple Cisco devices. The IP address for the gateway router is 192.168.16.3. What command line statement sets the correct Gateway of Last Resort?

A. ip route 0.0.0.0 255.255.255.255 192.168.16.3

B. ip gateway 192.168.16.3 255.255.255.255 0.0.0.0

C. ip route 0.0.0.0 0.0.0.0 192.168.16.3

D. ip default 255.255.255.255 192.168.16.3 255.255.255.255

You are working for a small business that recently purchased some Cisco switches and you have been asked to change the IPv4 address on one of the gigabit Ethernet ports. What commands would set the IPv4 address to 192.168.16.1 with a subnet mask of 255.255.255.0 from the configuration terminal for device 0 and port ID 2?

A. interface gigabitethernet 0/2 ip address 192.168.16.1 255.255.255.0

B. interface gigabitethernet 2/0 ip address 192.168.16.1 ip subnet 255.255.255.0

C. interface gigabitethernet 2/0 ip 192.168.16.1 subnet 255.255.255.0

D. interface gigabitethernet 0/2 ip address 192.168.16.1 netmask 255.255.255.0

A small business has HSRP configured on two Cisco devices; however, one device is very old and not very powerful so they really do not want this device to handle traffic except as a backup. The interface is on vlan 1, it is using group ID 10, and the priorities on both devices have been left at their defaults. What commands should be run on the better device to ensure it takes priority whenever it is available?

A. standby hsrp priority 110 standby hsrp preempt 10

B. hsrp priority 110 10 hsrp preempt 110 10

C. hsrp 10 priority 110 hsrp preempt

D. standby 10 priority 110 standby 10 preempt

You are working for XYZ Corporation and are required to configure LLDP in your environment. You have configured LLDP on the switch and now you want to verify if everything is configured correctly. Which command will you issue in order to verify if there is any LLDP TLV?

A. Switch# show LLDP tlv-select

B. Switch# show LLDP tlv

C. Switch# show running-config

D. Switch# show LLDP timers

What is the advantage of having end-to-end VLAN's over Local VLAN's?

A. Users are placed in a specified VLAN that depends on the physical location of the users.

B. All the resources are confined to a single location.

C. Depending upon the physical location, the users are restricted to access the internet.

D. Are very effective for large infrastructure where a lot of switches are connected independent of their physical location.

In a multivendor network, which is preferred?

A. Local Database

B. RADIUS

C. TACACS+

D. AAA

Which of the following are not the types of traffic defined in a SPAN session? (Choose all that apply)

A. Transmit

B. Monitor

C. Ingress

D. Receive

To troubleshoot the err-disabled recovery, what should be the first step if err-disabled is confirmed?

A. Erase flash

B. Issue the commands "shutdown" and "no shutdown"

C. Reboot the switch

D. Update the firmware of the switch